Alive!

Yes, it all went quiet, but there has been some progress;

1) The motor shaft adaptor got made. The motor cartridge has an internal spline but I didn't have a matching driveshaft and getting a one off spline cut is close to impossible in this country. Instead I had a castellated piece made and ground the end of the motor sprocket to match. This is attached to a tube which passes through the motor and engages with the gearbox input shaft. To get the spline for that I had to buy a clutch on ebay and extract the centre out of it, which was then turned down and welded into the tube.  All a bit agricultural, but it feels OK so fingers crossed it will take the torque and not cause too much vibration.

2) The motor then needed its electrical connections making - this wasn't straightforward either! The stator terminals are recessed so I machined some solid copper spacers to bring them out clear of the casting so that cable lugs could be bolted down.

3) Then finally on to the wiring.  Actually no, before that, I made a bit of aluminium framework to support the inverter and contactor. This allowed all the wiring to be done with it out on the floor, and then lifted up into the space where the radiator and fan was, where it picks up the original vibration damped mounting points.

The contactor is a temporary one, the voltage I'll be using really calls for a gas filled Kilovac or similar, but I had a big two pole Sagem contactor (rated for about half the voltage).  Good enough for now with the contacts wired in series.
The RMS inverter is a lovely bit of kit, the manual and utility is excellent and apart from one small wiring error on the resolver connections it all checked out and I was able to do the calibrations and setup.

Since it was in and wired up, I couldn't resist trying it. For a quick test I ran the inverter off mains power - just a bit of two core flex plugged into a socket with a bridge rectifier attached gives 360VDC. With some trepidation I donned the safety goggles and clicked the switch to forward. As soon as I touched the throttle the lights dimmed, the motor whirred and the jacked up tyre span. Forwards! Amazing.

Now to put the batteries in and make it work properly...

On rails

I found a whole evening to spend on this project, and used it and most of a bottle or Argon to weld up the front battery support rail. Aluminium welding skills are slowly improving but it's not exactly beautiful, so no close ups! 

And here it is installed in the car, ready for the battery boxes to be bolted in.

A long wait

Too long a wait, but I finally got back into the metal workshop today and made the first of two battery packs for the front of the car, and the supporting structure that will bolt on to existing bearing points in the car.

The design of these required a bit of head scratching as the packs have to be easily removable, miss all the bits that can move such as the steering linkage, and fit under the bonnet. And it's all got to be aluminium... just because.

So, instead of a battery box (there just wasn't room) the cells support themselves and are clamped between end plates which are welded to box section beams, which in turn bolt down to the support rails in the engine bay. Seems to fit OK, more pics next time!

Motorin'

Motor in, more or less

The aluminium adaptor plate came back from Jetcutit in Glasgow, and fit perfectly onto the dowels. Phew! The tooth pattern to accept the motor required the slightest bit of fettling but soon went snugly together.

The next step was to reattach the assembly to the car.  

A suitable means of supporting the motor end from the original engine mount had to be devised, and this required a bit of head scratching. In the end I used (recycled) a length of lightweight box section, as a bridge between the engine mounts, supporting the adaptor plate and the overhanging weight of the motor at the mid point. This is not the normal approach but it is straight forward, reasonably light and seems strong enough.

Abracadabra

I've got a horrible cold this week so haven't felt even slightly like doing anything, but I did have a think about how to attempt the next task on this project, that is, joining the electric motor onto the Honda gearbox.  

There you can see the gearbox bell housing, which would normally surround the clutch and flywheel.  We're not needing either, but the bell housing is cast as part of the gearbox so we have to work with it.  Simple enough - slap a metal plate across the front with suitable mounting points for the motor. The devil is in the detail of course - the first problem being how to replicate the outline to cut the plate so that it fits neatly.

I decided to try tracing the outline onto a sheet of cardboard, and use a hammer to tap through the dowels so that they are replicated precisely (like making a gasket).

Then somehow get it into the computer.

Just like magic! Or Tron, possibly.

The unusual castelated detail on the front of the motor can also be cut in to the plate, centred on the driveshaft, so that it just slots in and clamps up easily and accurately.

Lump

Time to remove the faithful little 3 cylinder engine. Definitely had mixed feelings about taking apart a car that was running reasonably well, especially as it's been totally reliable. 

Well past the point of no return now though! Seemed easiest to remove the complete transaxle, it looked like it would exit downwards after removing all the pipes and wires and the under-trays, and it wasn't too bad, taking about 4 hours in all.

It was a lot heavier than I expected!

Should be interesting to find out how much of that the hybrid motor accounts for.

The next step will be to separate the gearbox from the electric motor and engine, and then see what's involved in attaching the shiny new motor.

Mode: metal god

Spent an afternoon wrangling £70 worth of aluminium sheet into what I will choose to call 'a box'

As the dimensions were too big (and the sheet too thick) to work in my metal folder, had to resort to large chunks of wood, angle iron and a big hammer to form the corners. As a result it's not terribly beautiful, but it'll do the job. Here it is in situ:

Whilst under there I also removed the exhaust, miscellaneous bits of heat shield and a 10 kilo lump of ballast!  Certainly the car is pretty light in the rear - you can actually lift the back end off the ground by hand.  But not for long - the batteries will weigh it back down!